Harley repair wiring harness plugs. SOLVED: Harley wiring diagrams 2019-01-24

Harley repair wiring harness plugs Rating: 8,9/10 1256 reviews

Khrome Werks Plug

harley repair wiring harness plugs

And yes the older bikes are 5 wire system so if you trailer is a 4 wire you need the converter. See our Hopkins 48895 converter. Place the motorcycle on a level and secure area. Work from wire to wire, cutting them by staggering the cuts about an inch or so apart see figure 5. Slide a piece of shrink tubing from kit over each of the wire ends stripped in step 9 and crimp the wires into the terminals installed in step 8.

Next

How To Wire A Harley Speedometer

harley repair wiring harness plugs

Notes: Suggested to use with 32-9314 tail. Handlebar and tail lamp wiring must be purchased separately. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. I know not everyone is going to be happy, and its not a huge deal, just a warning. Route new wire harness 2 through the hole in bottom of the billet headlamp shell A. Use either butt connectors provided or customer supplied connectors.

Next

Boom! Audio System Wiring Harness

harley repair wiring harness plugs

Most common is 3 male pins and 1 female pin. Depress the external latches and use a rocking motion to separate the pin and socket halves. Be advised that all orders placed on BikerDirect. I followed the diagram and it went together quickly with the supplied connectors. What it sounds like is that one half of your breaker is tripped, and the remedy is to trip the double breaker in order to reset the half that is tripped.

Next

Harley Wiring Harness

harley repair wiring harness plugs

Attach the white ground wire supplied to frame close enough to the compressor, so the wire will reach. Remove speedometer, bracket, and harness. Slide heat shrink tubing over connectors installed in steps 10 and 14. Cycle repair books should be in 646 stacks of reference. Adapter ring from kit Figure 6, Item 1 will be used to install billet headlamp assembly on Instruction Sheet-J03018. Cut wires and techflex to proper lengths. Main Harness Note: If the optional factory connector kit is being used, please disregard this section of the instructions and refer to the instructions supplied with the factory connector kit.

Next

Boom! Audio System Wiring Harness

harley repair wiring harness plugs

I bought this harness to accommodate new Tour Pack speakers and also an iPod interface. Do not remove front gasket from the speedometer. Place wires from speedometer through front of left opening in double bracket. Make sure the bolt is tight! Now is the time to make sure all is well with the harness. Take any slack out of the loom, keeping it up against the frame and away from the engine or exhaust, using several of the small cable ties provided. Guide the new wire harness from the Signal® mirror to the electrical wiring. Register a Free 1 month Trial Account.

Next

LED Headlamp Wiring Harness

harley repair wiring harness plugs

This allowed them to fit the connector. Replace cover and boot from reset switch. You will now see three sets of electrical connections to the unit main body. Lift the console and remove the old speedometer from the console. Handlebar and tail lamp wires must be ordered.

Next

Harley Wiring Connectors

harley repair wiring harness plugs

All trademarks and trade names referred to on the BikerDirect. The back clamp will complete the alignment. I soldered the fuse block to the red power wire and use heat shrink tubing to make that connection more weather proof. Follow the frame to where the back bone and seat support rails come together. Came back upstairs and to look at stove, the burners are working fine so I continued to preheat oven after a half an hour the oven was only slightly warm. Turn ignition on and test horns. Before proceeding review User Guide document for detailed instructions on following procedure.

Next

Harley Davidson Wiring Harness Transfer

harley repair wiring harness plugs

Longer wires would allow it to go under the seat with the battery. It is best to work front to back. Once you follow his instructions and drain the fuel tank filter, cleaning any dirty parts and tightening any loose bolts, you can refill. Disconnect battery cables, negative cable first. All of the harness plug connections must go together with ease, meaning none should require any force to connect.

Next

Reading : Harley Repair Wiring Harness Plugs

harley repair wiring harness plugs

Activate shrink tubing with heat gun or hair dryer. One wire is silver, one is copper colored. Includes the main turn signal wires. Term Wiring can be confusing and, sometimes troublesome. Tape end of one black wire with electrical tape and secure it to wire harness. Some models have front directional lights equipped with three wires, the third black wire is a ground wire.

Next

CUSTOM MOTORCYCLE WIRING HARNESS — BROKEN SPROCKET GARAGE

harley repair wiring harness plugs

Set initial odometer value 4. Handlebar and tail lamp wiring must be purchased separately. Proceed to Setup Section below. Improper installation of this kit could result in death or serious injury. Handlebar and tail lamp wires must be ordered separately. Unplug the unit from the mains power.

Next