They are made in China and i am finding that the quality of this radio is what you come to expect from a chineese product. It's packed with all the features and reliability of the Cobra 29, plus NightWatch technology that illuminates the radio controls for easy use in the dark. Now comes with this external Microphone!!! Channel 19 is unofficially regarded as a general-purpose channel to make contacts and listen to conversations and reports of traffic and road conditions. Professional driver-requested improvements have been made thru-out the years to continue to enhance performance and durability continuing the un-matched Cobra tradition. Now for the dead key. NightWatch technology fully illuminates the radio's function settings for easy viewing at night.
The unique, solid-state, electro-luminescent backlighting is powered by a dedicated integrated circuit to maximize night vision while minimizing eye fatigue. Enter your Gmail so we can send a share to our Google drive for you to view. All Hazards Alert weather receiver plus NightWatch Electroluminescent illumination technology that allows the user to view the radio settings at night, and receive up-to-the-minute weather information and alerts even when the radio is off. Channel 9 is reserved for emergency communications. Includes a 6 Knob set , parts and labor. So start with your knob all the way counterclockwise and turn slowly in the clockwise direction until the white noise stops.
For proper operation the squelch should be adjusted so that you have the gate open as wide as you can without hearing the white noise. If you want to remove talkback, just open the case, flip it tothe solder side, and remove that resistor that was installed, or you can replace it with a new resistor and still have talkback. Cobra can actually switch that out fairly cheap. The radio's performance will not be effected by this. This is actually a good thing. I have at least 10 of these on my shelf because their not worth the cost to repair and they all seem to have the same problem with not transmitting.
The backlighting is powered by a dedicated circuit designed to maximize illumination while minimizing eye fatigue. NightWatch technology illuminates the radio's function settings for easy viewing at night. A dimmer control adjusts to all lighting conditions. Instant Channel 9 - Immediate access to emergency channel 9. You will have to solder the two wires to the new meter, observing which post they came from, this will determine the direction the meter swings. Here is a link to the Modification Instructions, so you can get a better understanding: If I left anything out, or you have more questions or need further clarification on anything, don't hesitate to email me. .
To change back to factory, remove the resistor that was soldered to the solder side, across the capacitor, then remove the capacitor. That should be the operating position. Cheaper than buying a face plate used on the net. If there is a capacitor, the it has been done. Enter your Gmail so we can send a share to our Google drive for you to view.
You just remove the light bulb and put it in the new meter casing with the rubber stay. If you have a lower dead key, this will allow you a larger range of power to swing. Ideal for night drivers who want a quality radio with all the features that's safe and easy to use in the dark. NightWatch technology fully illuminates the radio's function settings for easy viewing at night. My personal favorites are the and. Now just install a jumper in the place. Make a completion video to show tune-up levels and modifications demo.
The squelch knob is like a gate for incoming signals. It functions both as a radio transmitter when sending messages and a receiver when receiving messages. The unique, solid-state, electro-luminescent backlighting is powered by a dedicated integrated circuit to maximize night vision while minimizing eye fatigue. You remove the case screws, the face plate screws, and then remove one screw and loosen the other that hold the meter inplace. A dimmer control adjusts to all lighting conditions. Antenna Warning Indicator - Illuminates when antenna needs checking. This will be self explanatory when you open the radio.
Yourse is probably squealing because the resistor is breaking down, I just fixed a radio 2 days ago with the same problem. It may have had a swing mod done, which drops the dead key down a couple watts. Make a completion video to show tune-up levels and modifications demo. The more resistance, the lower the talkback volume. The face plate goes out often on these radios. The unique, solid-state, electro-luminescent backlighting is powered by a dedicated integrated circuit to maximize night vision while minimizing eye fatigue. The drivers can hear just fine but when they transmit no body can hear them.