Gently pull off the panel. I did not see a switch around the lift gate that would sense it open though. See product for application and installation details. Remove that then you have to literally pry the arm up and off. I did carefully remove the bracket and then the gear cover to make sure the gear was in good condition and the armature shaft seemed tight into place.
Bottom Line The product arrived at my door quickly and was packaged nicely. I just did this although I ran out of light and did not have time to diagnose my likely bad motor problem. I was going to get it replaced, but I really didn't feel like sending it back and waiting for a replacement. You can also run 10w30,or even the diesel oil 15w40. Now nothing I can do to get them to go down in the off position. So I attempted to grind down the threads with my Dremel and to my surprise, I was successful and the nut went on smoothly. Re-solder the contacts on the wiper control board.
The manufacturer really should implement some better quality control though. Or you may just be struggling to keep it highway-approved. Posted on Jul 20, 2010 They haven't been removed since the windshield was replaced several years ago. Gently pull back the plastic covering the covering the metal frame. I will upload the instructions to fix this problem, if there is interest. I am not very good with cars at all.
Sometimes without the parking pawl install correctly, the wipers park anywhere and delay operation is erratic. They haven't been removed since the windshield was replaced several years ago. No matter the situation, Advance Auto Parts has the Wiper Motor product you desperately need. Will burn the tires off or drag 12,000 pounds around no problem. Worked fine in the rain, made a stop, turned the car back on and once after hitting the mist mode they went up instead of down when they were done. Then open the hood,from inside y … ou can lift the cowl Have to be caerfull with edges ,they have clips at the ends. Or its position switch needs adjusted while testing.
Replacing this motor after buying the replacement took me 15 minutes. Remove the rubber line and the electrical connection and pull the pump out. Let me know if you need anything else. The manufacturer really should implement some better quality control though. Look online for the wiper module for this model. For the recall they only replace the transistor board in the motor. All Replacement brand items are backed by 1-year, unlimited-mileage warranty.
Answer The engine size as well as a little more about the Truck model would have helped. This is a common issue to include operation without the switch being activated. Most likely the circuit board is bad. So I attempted to grind down the threads with my Dremel and to my surprise, I was successful and the nut went on smoothly. My Chevrolet dealer took the numbers off my truck and gave me a replacement internal wiper motor board free based on the recall. Windshield replacement is some serious bucks.
Today I picked up a motor assembly and wiper arm from i think a 98 or 99 expedition at the junk yard for 11 bucks. A used one will probably have the same problem. Sometimes without the parking pawl install correctly, the wipers park anywhere and delay operation is erratic. Haven't had any problems since until yesterday. Remove it and remove the blade arm assembly. I will open it up and check that the gear is not cracked like my old one. I wrapped it up at home with the reinstall of the panels.
Reverse above to put the new one back on. Jul 11, 2009 This is a common problem with Chevy Venture, Olds Silhouette, and Pontiac Montana. You don't need any solder just heat the cold solder joints for 3-5 seconds until the solder melts and this will re-connect the contacts. The motor should be on the firewall. .
We only sell parts from trusted brands like so that you can find quality parts you can count on. It's a very easy part to replace. Worked fine in the rain, made a stop, turned the car back on and once after hitting the mist mode they went up instead of down when they were done. During your testing, affix a temporary indicator pointer to the end of a wiper arm drive shaft use masking tape or similar to prevent damage to motor or levers. Bottom Line recommended Easy to install and has a real picture of the motor, parking pawl, not a universal drawing. The bottom screws on the air intake grill simply unscrew, but they screw into plastic inserts that are probably stripped out. Simple thins so easily over looked.
This product serves as an exact replacement for the old factory unit. On top of low prices, Advance Auto Parts offers 2 different trusted brands of Wiper Motor products for the 2002 Chevrolet Venture. My truck started to do the same thing. Now nothing I can do to get them to go down in the off position. Remove the 4 or 5 torx screws that hold the cover on the wiper motor it's on the upper rear firewall the circuit card is under the cover, lightly touch a iron to the cold solder joints, they will look dull until you heat them up. I tested it in the parking lot after simply connecting the harnesses together, yep all 4 positions are functioning.